How to make light up double slider card.

Hi, crafty friends!

Today I make light up double slider card using Chibitronics and Lawn Fawn stamps and dies.

When you pull the pull tab, the side panel extends and the heart constellation glows.

I'm using these stamps and dies.
"Lawn Fawn double slider surprise"

"Lawn Fawn winter skies"
"Lawn Fawn winter skies lawn cuts"

"Lawn Fawn upon a star"

"Lawn Fawn stitched hillside borders"

What you need to make a light up card is like this.
"Chibitronics Red, Yellow, and Blue LED Sticker Pack"
"3V coin cell battery (CR2016)"
"5mm wide Copper tape"

I'm using these inks.
"Distress Oxide ink salty ocean"
"Distress Oxide ink broken china"

I'm using these papers.
"White cardstock"
"White vellum"
"Plastic sheet"
"Red cardstock"
"OPP plastic sheet"

I will make the parts referring to the picture below.

Two pocket pieces. Die cut one of the two with notch die.
Two panel pieces.
3 x 4.25 inches white cardstock for back panel.
Die cut the white cardstock with panel piece and hillside border die.
Die cut the white cardstock with pocket piece and hillside border die.
Small white vellum.
Die cut the plastic sheet with track piece die.
Die cut the red cardstock with pull tab die.
Three 0.5 inch square switch parts.
OPP plastic sheet 2.5 inches wide.
2 x 4.25 inches white cardstock for inside panel.

Stamp the bears and four trees onto white cardstock. Color the motifs with Copic markers. (C0, C1, R24, R29, G07, G28, E27) Die cut the motifs using the coordinating die.

Make the pocket piece and panel pieces.

Stamp the heart constellation onto pocket piece using Versamark.
Stamp the constellation and sentiment onto panel pieces using Versamark.
Heat emboss with white embossing powder.
Using the ink blending tool and distress oxide ink, add in the color onto the pocket and panel pieces.

Adhere the border, bear and tree parts on the pocket and panel pieces.

Make the holes at the position of the lights.

Put the colored pocket piece on another pocket piece, mark the position of the lights.

Put the track piece on the pocket piece, draw the outline of the track piece.

Align the left edge of the pocket and panel piece, draw a line at the right edge of the panel piece.

Make the circuit.

Draw a line 1/2 inch from the score line of the pocket piece. Draw three lines at 1/4 inch intervals.
Draw the lines 1/4 and 3/4 inch from the left edge of the pocket piece. (Line A and B)
Draw a line 1/8 inch from the right edge of the panel piece. (Line C)
Make a 1 mm wide slit between Line A and Line C.
Mark the position of the battery and Chibitronics.
Draw the circuit with a pencil. Make sure the negative side circuit crosses the left edge of the slit.
Cut out the position of the battery with a craft knife.

Put the circuit card base on the back panel, mark the position of the battery.

Put the double-sided tape on the skinny tab of the pocket piece. Adhere two pocket pieces together.

Adhere the copper tape on the drawing path. At the position of the battery leave about 1 inch of copper tape and cut it.

Make the switch part.

Fold square parts in half and insert the switch part into the slit.
Place the switch part on the left end of the slit and adhere the copper tape.
Pull the switch part out of the slit and adhere copper tape around it.

Put the double-sided tape on the switch part.

Adhere 0.5 inch square part on the back of the switch part.

Put the double-sided tape on the position of the battery. Put the thin foam tape around the back panel.

Adhere the back panel on the back of the pocket piece.

Peel off the release paper, adhere the negative side copper tape, turn it back and cut it. Place the battery on the copper tape and adhere the positive side copper tape on the battery. Adhere the yellow Chibitronics on the mark.

Adhere copper tape on the Chibitronics to reinforce.

Place the inside panel on the pocket piece, mark the position of the lights. Make the holes at the position of the lights. Adhere the inside panel on the pocket piece.

Make the slider mechanism.

Put the double-sided tape on the end of the OPP plastic sheet.
Wrap the OPP plastic sheet around the track piece and paste it.
Cut out extra OPP plastic sheet.
Apply the double-sided tape to the top and bottom of the track piece.

Assemble the slider mechanism.

Place the switch part on the left end of the slit.
Put the track piece on the pocket piece, insert the left panel piece and check the position.
Peel off the release paper, adhere the left panel piece on the switch part.

Put the double-sided tape on the right end of the left panel piece. Adhere vellum paper on the back of the heart constellation.

Adhere the track piece on the pocket piece.

Align the left edge of the pocket and panel piece, and place the double-sided tape attached to the slider part on the right end.
Adhere the bottom end of the track piece on the pocket piece.
Adhere the left panel piece on the slider mechanism.
Adhere the top end of the track piece on the pocket piece.