Today I make light up snow globe tags using Chibitronics and Papertreyink's Tinsel & Tags Kit.
This kit is a very popular limited kit released in 2014.
If you could get it, try making a glowing tag!
I'm using these dies and stamps.
"Papertreyink Make it Market Kit Tinsel & Tags"
"Papertreyink Make it Market Kit Tinsel & Tags Trimming Kit"
(Sorry. This kit has already retired.)
"Hero Arts Circle Infinity Dies"
What you need to make a light up card is like this.
"Chibitronics Red, Yellow, Blue MegaPack"
"Chibitronics circuit stickers effects add-on"
"3V coin cell battery" (CR2016)
"5mm wide Copper tape"
I'm using red, blue, kraft, white cardstock, vellum paper, 2mm thick foam sheet and double-sided tape.
I'm using these inks and markers.
"Altenew Caramel Toffee Crisp Dye Ink"
"Altenew Crimson Crisp Dye Ink"
"Altenew Frayed Leaf Crisp Dye Ink"
"Altenew Evergreen Crisp Dye Ink"
"Altenew Mocha Crisp Dye Ink"
"Altenew Jet Black Crisp Dye Ink"
"Tsukineko StazOn Jet Black Ink"
"Copic sketch marker E31"
I will make the parts referring to the picture below.
- Die cut a kraft cardstock with the scalloped circle die.
- Die cut a 2mm thick kraft foam sheet with the scalloped circle and circle dies.
- Die cut a white cardstock with the circle die for circuit.
- Die cut a blue cardstock with the snow scene die.
- Die cut a vellum paper with the circle die.
- Die cut a 2mm thick white foam sheet and double-sided tape with two circle dies.
- Die cut a white cardstock with tree, snowman, deer scene dies.
- Die cut a white cardstock with the house and roof dies.
- Die cut a red cardstock with the small banner die.
- Cut the vellum paper for the windows.
- Pull tab parts (0.5 x 2 inch)
- Switch parts (0.5 x 0.5 inch)
Stamp the parts refer to the picture below.
- Color the wood parts with frayed leaf ink.
- Color the tree trunk with E31 copic.
- Stamp the leaf using evergreen ink.
- Stamp the snowman and sentiment using jet black ink.
- Stamp the deer using caramel toffee ink.
- Stamp the wall and chimney using mocha ink.
- Stamp the door and roof using crimson ink.
- Stamp the window on the vellum using StazOn.
- Cut off the tab of the house part.
Adhere vellum paper on the back of the
windows.
This circuit consists of three layers.
This is the top layer.
- Cut off the roof of the snowman scene part.
- Mark the position of Chibitronics in the middle of the house part.
- Draw the circuit with a pencil.
- Make a rectangular hole to pass the copper tape through the lower layer.
Put the snowman scene part on the tree
scene part and snow scene part, trace the rectangular hole.
Cut out the rectangular hole.
Put the snow scene part on the scalloped
circle part and mark the lights and hole with a pencil.
This is the middle layer.
- Doubles the length of the rectangular hole and cut out.
- Mark the position of the Chibitronics and the effect sticker.
- Draw the circuit with a pencil.
This is the bottom layer.
- Draw a center line on a circular part.
- Mark the position of the pull tab part.
- Put the scalloped circle part on the circular part and mark the hole with a pencil.
- Mark the position of the battery.
- Draw the circuit with a pencil.
- Mark the position of the slit and cut out the 1/32 x 1 inch slit.
Adhere the copper tape on the drawing path of the top layer and adhere the yellow Chibitronics on the mark.
When adhering to the hole place, cut the
copper tape leaving about 2 inches.
Adhere the copper tape on the drawing path of the middle layer.
- Connect "-" of Chibitronics to signal pad of the effects sticker.
- Connect "-" pad of the effects sticker to "-" of the battery.
- Connect "+" of Chibitronics to "+" pad of the effects sticker and "+" of the battery.
- Adhere the yellow Chibitronics and the effect sticker on the mark.
Adhere the copper tape on the drawing path of the bottom layer.
- Adhere the double-sided tape on the position of the battery.
- In the position of the battery, adhere the copper tape on the double-sided tape.
- Place the battery on the copper tape with the positive side up.
- Adhere the positive side copper tape on the battery.
Make a switch part.
- Fold square parts in half.
- Insert the switch part into the slit.
- Adhere the copper tape to the same position as the copper tape attached to the circuit paper.
- Pull out the switch part from the slit.
- Adhere the copper tape around the switch part.
- Make cross-shaped parts like this.
Apply a double-sided tape on the switch
part and adhere the pull tab parts on the switch
part.
Adhere the pull tab parts on the back side.
Adhere the double-sided tape on the back side of the card
base.
Adhere the card base on the scalloped
circle part.
Adhere the foam sheet around the card base.
Adhere the scalloped circle part on another
scalloped circle part.
Adhere
the copper tape on the upper half of the base copper tape and cut.
Put the snow scene part on the foam sheet
and mark the snow.
Mark the outline of the snow and cut the outline with scissors.
Adhere vellum paper and a foam sheet on the back of the snow
scene part.
Adhere the snow scene part on the scalloped
circle part.
Adhere the house part on the snowman scene
part.
Adhere the tree scene part on the snow
scene part using thin foam tape.
Adhere the snowman scene part on the tree
scene part using thin foam tape.
Adhere the copper tape on the lower half of the base copper tape and cut.
Adhere the roof part on the wall part.
Adhere the deer scene part on the snowman
scene part using thin foam tape.
Adhere the small banner on the snow scene
part using thin foam tape.
Adhere the miniature tree and the cotton snow on the deer scene
part.
Adhere the clear tag dome on the scalloped
circle part.
Put the red bakers twine through the hole.
I finished it!
When I pull the pull tab, the stars flash
and the windows glow.
Be sure to check out the whole video tutorial for more details.
Thank you for stopping by!
Love these!!
返信削除