How to make light up roller coaster card.

Hi, crafty friends!

Today I make light up roller coaster card using Chibitronics and Stampin' Up stamps and dies.

When you open the card and pull the pull tab, the stars flash and popcorn stand glows.

I'm using these stamps and dies.

"Stampin' Up Thrill Ride Pop-Up Thinlits Dies"

"Stampin' Up Let The Good Times Roll Photopolymer Stamp Set"

"Lawn Fawn starry skies die"
"Lawn Fawn push here stamp set"

What you need to make a light up card is like this.
"Chibitronics Red, Yellow, and Blue LED Sticker Pack"
"Circuit Sticker Effects Add-on"
"3V coin cell battery (CR2016)"
"5mm wide Copper tape"
"Conductive Fabric Tape Patches"

I'm using these papers.
"Tim Holtz Idea-ology deco sheets"
"Black, navy, white, yellow cardstock"
"White vellum paper"

I will make the parts referring to the picture below.

Two black cardstock (4.25x5.5inch)
5.5x11inch navy cardstock
Small white cardstock for die cut parts
White vellum paper
Silver deco sheet
Black cardstock for sentiment banner
Two pull tab parts (0.5x2inch)
Two switch parts (0.5x0.5inch)
Navy cardstock for pop-up part (0.5x2inch)
Yellow cardstock for flags

Stamp the coaster, present and popcorn stand and die cut. Die cut yellow cardstock using the flag die.

Cut out the wall with a craft knife. Put one popcorn stand part on the other part and mark the light with a pencil.

Adhere vellum paper on the back of the popcorn stand.

Stamp the sentiment using Versamark and heat embossing with gold embossing powder.

Die cut navy cardstock using the roller coaster die. Align the 13 mm from the bottom of the die with the center line of the card.

Die cut silver deco sheet using the roller coaster die and cut along the line.

Adhere the silver coaster parts on the navy cardstock. Die cut navy cardstock using the stars die.

Fold along the score line.

Fold 1/2 inch width cardstock and make pop-up part. Adhere the pop-up part on the lower right of the roller coaster.

Looking from the side it is like this.

Make a slit through the copper tape at the root of the pop-up part.

Put two black cardstock 2 mm apart with washi tape.

Put the navy cardstock on the black cardstock and mark the light with a pencil.

Make the circuit.

Draw three lines at 1/4 inch intervals from 1 1/2 inch from the bottom.
Draw a line of 1 inch length from the 3/8 inch from the right end of the center line.
Cut the slit with 1 mm width with a craft knife.
Mark the position of the Chibitronics and battery.
Draw the circuit with a pencil.

Adhere the double-sided tape on the position of the battery.

Adhere the copper tape on the drawing path.

At the position of the slit leave about 2 inch of copper tape and cut it.
At the position of the battery, peel off the release paper, adhere the negative side copper tape, turn it back and cut it.
Attach a conductive fabric tape to the fold line of the card and reinforce it.
At the position of the slit leave about 2 inch of copper tape and cut it.

Adhere the Chibitronics and effect sticker on the mark.

Adhere copper tape on the Chibitronics to reinforce.
Place the battery on the copper tape with the positive side up and adhere the positive side copper tape on the battery.

Make the switch part.

Fold square parts in half and insert the switch part into the slit.
Place the switch part on the right end of the slit and adhere the copper tape.
Pull the switch part out of the slit and adhere copper tape around it.
Insert the switch part into the slit and confirm that the LED turns on.

Put the double-sided tape on the switch part. Adhere the pull tab parts from the front and back. Adhere two pull tab parts together with thin foam tape.

Adhere vellum paper on the back of the insert panel.

Adhere the popcorn stand part on the pop-up part.

Put the foam tape on the lower half of the back side of the navy cardstock.

Put the double-sided tape on the upper half of the back side of the navy cardstock.

Pass the copper tape through the slit. Adhere the navy cardstock on the black card base.

Adhere the copper tape on the popcorn stand. Adhere the Chibitronics on the mark. Adhere copper tape on the Chibitronics to reinforce.

Adhere the flag parts, popcorn stand and the coaster parts on the navy cardstock.

Adhere the sentiment banner on the navy cardstock.

Make the cover panel.

Stamp the sentiment and line onto the cover panel using Versamark. Heat embossing with silver embossing powder.

Adhere the coasters and the popcorn stand. Put the double-sided tape on the back of the cover panel and adhere the cover panel on the black card base.